Bench-Type Circular Saw Maximum 2000 W, Saw Blade with Height/Angle Adjustment Facility, Parallel Stop, Angle Stop +/- 60° 4340490

Now this was a very pleasant surprise as to size ! Even without the extra add-ons to width this still like a dinner table for two. Easy to follow set up just do not over tighten bolts as dud on one of the legs. Decided before if table wide enough before going into fitting the extra width . Do check saw is set right as in instructions I did a couple test cuts before the table guide was accurate. You do and will need a proper hoover to suck up sawdust, do not think a normal household one will do trust me it won’t ! Get a 20lt min wet dry one . Over all very happy with it . Oh one thing I’m adding on is two wheels to make it easy to move about so decide where you use it if it going to need moved about as the extra support legs are flimsy if you move it as buckle under wieght . But value fir money ? Yes very much so, I have the smaller size one two and it a quarter size of this one. 🌟🌟🌟🌟🌟🌟🏴󠁧󠁢󠁳󠁣󠁴󠁿🌟🌟🌟🌟🌟

First things first. It cuts. It arrived as expected with Amazon. A good buying and delivery experience. Upon opening it was apparent the table was bent. I had two options, return and await a new one to be delivered, or be impatient and manually bend the thin metal back into place and utilise a spirit level to tell me when to stop. I was impatient. No drama, I done what was needed. As I was planning to build a cross sled and use the saw mainly for small cross cuts this wasn't an issue. So accuracy, it needed adjusting. Do not trust the angles on the saw tilt. You set it to 0 and it'll actually be about 10 degrees. I purchased a digital angle finder and trust in that. The tape measure and measurement finder on the table. Not accurate, about 3-5mm out. If ripping material with the fence I'd recommend using a metal rule and your eye for this and not relying on the manufacturers guides. Again, this isn't an issue for me as I built my own sled using the 5 cut method and now have accuracy to withing a thousand of an inch. Ease of use. It spins really fast and cuts wood, and also fingers. It's a simple plug in (3 pin), hit the green button and cut. Comes with a push stick (buy another for two directions of pressure). Value for money. I certainly wouldn't buy cheaper, but for what I needed it for, small projects utilising a push sled, it's perfect and didn't cost the Earth. Yes there are better out there, yes I one day aspire for bigger, but this is really all you need for small garages and projects. Oh, it's very messy. I hook it up to my Kercher W2 hoover. Next to useless. The hoover sucks fine, but the dust seems to chuck down to the floor and not the hoover extraction pipes fitted at the rear. Could this be rectified with a high volume low pressure vac? Probably. Do I want to spend hundreds doing do just yet? Nope. Just a forewarning to fellow hobbiests that your wives/husbands may well moan about covering your darling sons bike in sawdust. Would I recommend this saw? Yes.

It's a bit of a faff to set up, but once assembled feels stable. Although it is made of abs plastic it feels substantial. The blade on mine was dead plumb and ready to go without adjusting. The rip fence is poor, but I normally use a straight edge with clamps anyway. It just the fence that lets it down. The riveing knife is easily removed,and I was able to rip down some 6x8 by double passing. It not a shepach by any strech of the imagination, but it's fantastic value for money. And I have actually almost made the purchase costs back on one job. If you understand it's limitations it's a good choice, strong and accurate enough for some workshop joinery and small enough for the site.

For the money it's good value. It's very good at the DIY level, and to achieve the best from this machine, some thought and refinement is needed. If you want professional super accurate first time every time finish, this is not that machine. But again, it is a good machine for the money.

Prodotto perfetto ,di facile montaggio .da provare il taglio e la lama . Rettifico la recensione, purtroppo non si possono aggiungere altre stelle ,né merita almeno 10,ho montato in 1 ore e poco più il tutto,ho provato la gradazione della lama e in poco e niente era perfetta,ho provato con del truciolato da 1,5 ed il taglio è molto soddisfacente con lievi scheggiatura,messo un disco con più denti ed il taglio è migliorato tanto sul truciolato.Consiglio questa macchina al 100% ,stabile veloce da riporre e da pulire,con aspiratore collegato la polvere si abbatte quasi a nulla .

Uppfyller mina förväntningar. Lätt att montera.

Ürünün kurulumunu yaptım fakat henüz kullanmadım. Ürün kalitesi yüksek. Beklediğim performansı da alırsam tam bir fiyat performans ürünü olacaktır. Şimdilik tek eleştirim kullanım kılavuzu ile ilgili. Kitapçık biraz karmaşık daha net ve kolay anlaşılır olursa kurulum daha hızlı olacaktır

Très belle scie fonctionne à merveille à part que pour le montage il manquait des ecroux et vis heureusement j'en avais mes pas les mêmes

Super , dommage que des ralonge ne soit pas disponible . Mais le pris très bonne qualité et marche bien