VideoSecu LCD LED Monitor TV Wall Mount for 19" 20" 22" 23" 24" 26" 27" 30" 31" Flat Panel Screen Maximum Loading 66lbs VESA 75/100 Ultra Thin Mount Bracket 1EA

I needed a mount for my computer monitor that would put it as close to the wall as possible and this mount was perfect. Sturdy, easy to install, and very low profile.

I was searching for something like this for some time. What a great way to be able to attach something to a wall and be able to move it around to another location if desired. While it then would require additional ones to be purchased, it is well worth it. You can also use it as a storage device, use it to hold something on a wall and easily lift it up to remove it and use it remotely. Might be nice if they made something larger for heavier items, but this one is pretty robust with a good paint finish.

Very easy to install. Works great. Fine quality. simply screw the back piece to the wall (on a stud) and attach the other piece to the back of the TV and slide the two pieces together. It's not meant for large TV's, but worked perfectly for installing a 22" in my trailer. I did note that one of the screw holes was a millimeter or so off center from one of the holes on the TV, but it wasn't much trouble coaxing the mounting bolt into place. It comes with a few different sizes of mounting bolts to accommodate the differences in TVs. As has been said, it does mount the TV very close to the wall, so if the TV is also very thin, swapping cables might be tricky. My only warning is that if you are installing this in a confined space, such as close to a ceiling, or in in a cabinet, you will need to have at least 6 inches above where you want to your TV to be positioned in order to slide the TV plate into the wall plate.

I purchased three of these to mount three LCD monitors side-by-side. They're very solidly constructed and the hold is very secure. All in all, the product does the job. However, the included documentation was not helpful. For example, the installation instructions called for using bolts that weren't actually included with the product (it came with screws in place of the bolts). Second, it only gave instructions for installation in a couple of different scenarios, neither of which applied to me. Therefore, the instructions were nearly worthless and I had to figure out how to install it on my own. In my case, I mounted the three LCD monitors to a 1"x8" board. To attach the rear mounting plate to the board, I decided to use the four 8mm holes in the "square" pattern on the rear mounting plate. I drilled four clearance holes in the 1"x8" board, one hole for each of the ones in the mounting plate. An 8mm drill bit is preferable for that task, but you could use a similar size fractional bit (e.g., 17/64th bit). Once the holes are drilled, you will want to use four M8 size bolts, four regular M8 size nuts, and four flat M8 washers. These will give you a very secure hold between the rear mounting plate and the board. Because they are properly sized to fit the hole pattern in the rear mounting plate, you will have little to no "play" in the position of the mounts -- this makes the fit nice and snug. Note that the drill bit, the bolts, washers, and nuts will need to be purchased separately from the mounts as this hardware isn't included with the mounts.

It does exactly what it purports to do: Mont a VESA monitor something like a half inch off your wall. Any thinner would be a drawback. If you have a really thin monitor, there won't be enough room for fingers behind it when you have it on the wall, so think about connecting the cables before hanging the panel. It doesn't pivot and you might find that you want it to pivot because the angles aren't perfect - tough luck! The price we pay for flush to the wall is that there is nor room for pivoting. In my application, I put up with suboptimal angles because I need it to sink into the wall as much as possible. For me, if it stuck out any more, the panel would obscure another monitor that I can't move. So think carefully about if you need it to pivot! If you need to pivot, this is not the mount you are looking for. Actually, it's the other way around - this is the mount you want ONLY if getting it as close as possible to the wall is the most important thing.

Even came with very short screws to mount the TV with. Works as expected and solid heavy metal construction. Easily would support a much heavier TV than my 32" LG at 19 lbs. I am using two of these in my office and guest room so I can slide the TV out of my office and into the guest room when we have company. ***Take note: In my case, it was actually too close to the wall to allow the cable coax connection because of the location and angle of the connection on my TV. I added a piece of 3/4 inch plywood behind it to provide the extra space. I may add a in-wall connection box later to solve this, but works/looks perfectly fine with the plywood behind it. This was not a negative to me because frankly, I can't understand who thinks it's a good idea to have the cable connector pointing towards the wall rather than down.

Sturdy and easy to install. Locate stud for added strength. Mount wall bracket, mount the other bracket to tv or monitor. Slides unit in place.

Great light duty mount. Very slim.

Excellent. Super strong.