Connect 120mm Screw Heavy Duty Dot & Dab Wall Fixings - 24 Box

Really strong fixings, easy to install, used for various projects and never had an issue. Will definitely use in future on dot and dab walls.

I spent some time shopping around and researching what I could use to hold a heavy shelf up to a plasterboard wall. My wall had 27mm insulated board, dot & dab, then brick. I fitted the plasterboard myself, and had squashed it on the wall quite hard, so little gap. I chose these plugs because I estimated there was at least 35mm from the finished surface to the brick. Even a 70mm plug would not have been anchored enough. I was impressed with the simple idea of inserting a metal core to provide strength, and never doubted that these would work. I had to buy the 120m length screws, as the shelf brackets were 15mm thick. I would say fitting them well, takes some skill and is not for an amateur. I used a small pilot bit to get my holes precise. Then an average 10mm masonry bit, will not be quite long enough to drill the hole, so either a long one, or not fully in the chuck for the last 8mm. I then had to use a long 6mm to make the hole slightly deeper, as the 120mm screws would need to go in further than the back of the plug (bracket 15mm thick). You need to be careful to clean the hole out, I used a screwdriver as if the dust gets packed in the end, the plug wont sit home. You can tell if a plug is not going to sit home, and if you are careful you can pull it out and improve or clean the hole. The screws are good quality. Hammering in the metal insert is very satisfying. I only had 2 issues. One hole must have caught a mortar joint, and was slightly off from the plasterboard hole. These plugs do not bend, so had to ream out the p'board. In tackling this, I broke one of the plugs just using moderate force to push it in. my only criticism of these plugs is that the final part near to the flange of the plug is fairly weak - due to cut outs for barbs. There is probably only 50% plastic remaining after the cut outs. Given that its not easy to get these holes 'just right' it would be nice if this part could be improved to allow a bit more robustness when fitting. I'm sure the damaged ones in other peoples reviews / photo's will have been due to not cleaning out the hole and hammering them until they crush. When fitted properly the flange sits a little proud from the wall, but not really noticeable and gives you something to clamp against. The only other issue is that it is hard to get holes in precise places, with a 10mm drill bit. If you don't have any adjustment on your fixing, then you need to take your time and be very careful. I ended up enlarging some of my bracket holes to compensate for the misalignment being a shelf with 4 brackets, it needed to be perfect. A TV mount wouldn't pose this problem. In hindsight, I should have taken my pilot hole into the brick, but I only went through the p'board. I would use again, without a doubt. Great product.

I purchased these to fasten a TV bracket through dot and dab, and they have been superb.

Do exactly as described

I was wanting some decent sized fixings to install some Ikea wall mounted furniture and a TV bracket and after some research I decided to opt for these. I opted for these plugs due to living in a new build with dot and dab plasterboard and wanting to get through into the block work to ensure the items being secured were not going to sag over time or fall off the wall. The Plug is long enabling you to secure into the block work, the metal sleeve insert is perfect for providing the support through the plasterboard and into the block work so it won’t sag. They are easy to put into a correctly sized hole with a hammer and are solid once the screw has been inserted to secure the item. The price is a little on the expensive side but worth every penny to ensure safety.

Great product, as always

I have quite a few walls that are block with dot and dab with plasterboard. I’ve always struggled with affixing things to these walls due to the gap between the plasterboard and the blockwork. Sometimes the plasterboard would pull in and get damaged or fixings become loose due to the gap. Thanks to the metal collar in these that bridge that gap, I’ve been able to affix heavier items to those walls and it felt like screwing in to solid brickwork. I keep a box of these in the garage and they are now my preferred choice of fixing on dot and dab walls.

I have bought these fixings before and found them to be very useful when hanging radiators I'm very satisfied with the product. Only small problem. I found the design of the box has been changed and now once opened the lid cannot be kept shut so found myself picking all the bits out the bottom of my work bag.

Eccellente. Funziona come pubblicizzato.

Sehr gute Qualität. Würde ich wieder kaufen.

Superbes fixations. Je les ai utilisés pour la climatisation et pour une télévision accrochée au mur. J'ai des plaques de plâtre avec isolation polystyrène sur mes murs et ces fixations sont idéales pour cette situation.