LINKUP PCIE 5.0 Riser Cable | for Vertical GPU Mount | Right Angle | Graphics Card GPU Ready | Usable with PCIe 4.0 & RX 9070/ RTX5090 | 20cm (Total Length: 24cm)

I had a PCIE 4.0 riser cable from Corsair that I grabbed when I bought my case way back, but being able to get a more build-specific length and connector orientation was so much better. Yeah, I know that I am probably not even taking advantage of the full bandwidth capabilities with my 5070ti going from a PCIE 4.0 to a 5.0, but I feel like the airflow gains without the previous massively excessive S-bend of flexible riser packed in between my GC and the MoBo isolating the card from the flow was worth the cost. Installed easy, comes with hardware if you need the standoffs/screws to mount to your case. Build quality feels good. So far it works well, looks good to have the GC vertical and not worry about sag, and in my mind now I’m getting everything out of my GPU without any bottlenecks to slow me down.

Worked perfect for my 7900xt when an older cable didn't.

Edit:: PC started freezing after a week. Thought it was everything else until I tried without the riser. Ordered a replacement and received one that was obviously used and/or damaged. Don't waste your money. Very good quality, perfect fit, easy to work with, and worked perfectly fine out of the box. Was having issues with new AM5 board and 50 series card using a 4.0 riser. This solved all the issues. I use the Lian Li vertical GPU mount and it paired great with it with 0 issues.

Yes, it works perfect with 5090.

Installed for a vertical gpu bracket from EK for the 011-D XL, worked great with it. Mobo is an Asus 870e-e Strix, does not run at x16, only x8. AIDA64 previously had shown the 5070ti running at x16 when connected to mobo, now shows x8. Checked bios settings to verify. Not a big deal as a gamer, but if you need the bandwidth for work try a different brand.

HIGH quality cable. Still yet to install and test it. Only comment I have is that it's super thin so handle it with care.

Works great so far on a merc air 9070xt

Item was exactly as described and exactly what I need to complete my build for my new PC and my vertical gpu mount for my new xfs rx9070 xt gpu in my corsair 6500x case.

The final component for my new build. They were sold out of the 15cm version so I bought the 20cm one instead. With the RTX 5090 Aorus Master mounted vertically you can't see the extra 5cm anyways. Lian Lis vertical GPU bracket only has a gen 4 riser. The AsRock X870E NOVA wifi 7 motherboard supports Pcie 5 so I grabbed this link up riser. Only ones in the market I know doing them.

Riser idéal pour profiter des dernières générations de cartes graphiques en PCIe 5. Vous profiterez de toute la bande passante de celle-ci. Mon boîtier ( Hyte Y70 ) était déjà équipé d’un Riser PCIe 4 et après l’acquisition d’une RTX 5090, je voulais avoir la meilleure connexion possible pour elle. Je l’ai tout simplement fixé au boîtier avec un petit collier rilesan noir et une vis, et cela ne bouge pas du tout.

Funciona perfecto con una 5080.

attention avec le riser, vraiment attention car, j'ai brûlé ma RTX 5090 astral

品質面では何も問題はないのですが、商品説明の互換性リストに誤りがあります リストだとMidori 5Lには直角20cmとありますが、正しくはデュアルリバース19cmが適正形状になります 該当ケースで検討の方はご注意ください 前述のとおり、品質面では非常に安定した動作をしてくれているので、もう少しサポート部分を頑張ってほしいですね