Creality Ender 3 V3 SE Hotend, Ender 3 V3 KE Ceramic Heating Block Kit with Quick-swap Nozzle, Upgrade Hotend Kit 300℃ High Temperature 600mm/s High-Speed Printing for Ender 3 V3 SE/KE 3D Printers

Easy install, nice high quality prints. Fits perfectly on ender 3v 3 se. Worth while upgrade if you plan on printing with materials that require temps higher than 250.

I must've had a bad stock hotend because after I upgraded to this my prints looked immensely better. Added to that I don't have to wait as long for the hot end to heat up as compared to the stock one on an ender 3 v3 se. I wish the tips were priced a little more accessible as well as their sizes. I had to really look to find a smaller tip than stock, I didn't buy it but it's nice to have the option for those ultra high quality prints. The PID calibration did not go as planned and it errored out, does not cause any problems with actually printing and I still have to research the cause.

This is the third hotend I bought. I do a lot of printing. I do think these hotends burnout faster then the standard hotend, the print results are much nicer with thus hotend. It comes down to what your looking for. It you aren't looking for better quality prints, stay with yhe cheap standard hotend. This hotend upgrade delivers I feel better quality prints. Its easy to install (much easier than the standard). The quick change nozzle is no quicker then the regular nozzles, but the the nozzles are better quality and what I feel makes a different on outcomes of prints. I do recommend this hotend if your looking for better quality prints, but keep an extra hotend ready. My hotends have lasted for around 8 to 9 months, but I also do alot of printing.

At some point, you are going to not pay attention to your printer for a little while, and at that exact moment, it's going to notice you aren't there, and will immediately start to clog. 'If' you catch it in time, you can just give it a wipe, put on a new sock, and go about your day. But if you don't... you'll be pleased to have one of these spare in a drawer, as you wait for the printer to cool, and then slowly detach the blob of PLA that is now solidifed around your ENTIRE hotend and heating block!

Hot end works great but do have a hard time getting the filament past the copper neck. The neck needs to be flanged or thinner at the top as the filament hits the neck and stops. It takes me forever to get the filament fed into the system.

This is a fantastic buy! I purchased this to replace my old hotend. A bonus to this is it comes with a hardened steel nozzle as well so you don't have to worry about longevity. The install process was straight forward and worked right away on the first print.

I got this part two times(one + a replacement) and then both times the part was faulty. The screws that hold the nozzle to the heat block do not stay in and they fall out. I hope they don’t fall out while you’re printing because the hot end will fall and damage your printer like it did mine. Amazon says this has been an issue and I’m hoping they can help me resolve the problem because now my printer is damaged. DAMAGED! Darlene with customer support was extremely helpful in a bad situation. She assured me that Amazon will make it right and help me. All in all, do not buy this badly manufactured part. Trust me and save yourself. Seems like the seller bought it on Temu for $2 and ripped me off for $34. Thank you Amazon for your help!

I have Purchased with the intention of getting an upgrade for my Ender 3 V3 SE. Unfortunately it did not work. The hottend easily lost temperature and this cause low quality prints.

Calienta mucho más rápido y las boquillas son mucho mejores que las originales. Vale la pena para una ender 3 v3 se.

Excellent hotend; it allows for higher printing speed, better material support for non-PLA stock, and less chance of installation error. Definitely worth the money. I think "Quick-swap" is a misnomer though. You still seem to need to disassemble the toolhead and remove the extruder to switch nozzles. The only time this saves saves you is that you don't need to hot-tighten afterwards. So just manage expectations; you're not popping these in and out much faster than the normal nozzles.

I read the reviews. I bought it. Bets what you need to know! DON'T over tighten your nozzle. I know, it's autopilot from your standard hot end. If it's too tight, you'll struggle getting it out and trust more than the nozzle. That's what the "wire breaking issue" is. It's not a design fault, it's not reading the instructions quite thoroughly enough. Want consistant temps for printing - er - spicier filaments? polycarbonate? ✅. TPU? ✅. PETG? ✅. Through a 1.0mm nozzle at Mach jezuz? ✅ ❌ Leaks ❌ Uneven heat ❌ Waiting for the hotend to heat up.... Honestly, I loved my stock Ender 3 V3 SE. A lot. We've put a lot of time in together. This is a low cost upgrade that will make every material you use print better at higher speeds. There are settings that might need tweaking - such is life of anyone with a 3d printer - but your temps will be stable forever. Just buy it already, you know you want to!

No lo recomiendo me quemo la placa lo instale con la impresora apaga verifique las conexiones antes de entenderla y después ya no hace el home correctamente ya cheque todo , finale de carrera, conexiones , cargue firmware de nuevo cambie al viejo hotend y mismo resultado.

I got one good print out of this and then it clogged up. I cleared the clog and then I could not get a good print. I went to take the hotend off and the teflon tube would not release. Also, the original screws for the fan would not fit the hotend's heat sink. I had to use longer machine screws that I had on hand. Terrible experience with it. I am returning it.