AUTOCLOVER Tape-On Rain Guards Window Visors 6 Pcs Set for Hyundai Santa Fe 2015 2016 2017 2018 / Window Deflectors, Out-Channel Vent Shades (Smoked)

Very happy with the the looks and installation of this product.

Edit: I've now put this through a car wash with a pressure washer. I was careful not to put too much water pressure on the adhesive parts or to put undue pressure on the visors. They stayed on well. This process did identify another negative. It's very difficult to dry the car window and underside of the visor without pulling on it. The adhesive held, but I worry about this repeated pressure weakening the bond over time. Even with this new found negative, I'm still happy with these and glad I bought them. Original: I've tried 2 in channel visors for my '22 Hyundai Santa Fe PHEV before landing on these. The in channels look better than these stick on, but didn't allow my windows to close fully. It is just a design challenge for the in channel design. As far as looks, these stick on don't look bad. My kids say it blends in with our black car and is not noticeable. This is exactly the look I wanted. The adhesion is impressive. It's not 3M tape, but it is very tacky. It's been on for a few weeks and one rain event. It's holding very well. Haven't taken it through a automated car wash yet, but will revise my review if it has any trouble with it. I didn't notice much, if any added wind noise. My car is used in town so the max speed is about 50-55MPH. It does keep the rain out with the window cracked. This was the main reason for getting this product. My PHEV doesn't have a heat pump so any HVAC in colder weather turns on the ICE motor. I wanted to be able to ventilate slightly in cold/rainy weather so the inside doesn't fog up w/o having the ICE turn on to use gas. This does exactly that and am really happy with it. This product does have a few small issues though. First, the install needs to be very precise and detailed. I found the best way was to use the 'hinge method' like cell phone screen protectors. I used blue painters tape to tape the product in place in a way to allow it to be flipped up like a hinge. This allows you to position the product very precisely and adjust as needed which is critical over the long spans. I peeled about an inch of the adhesive backing and folded the visor down in place. I could then pull the backing off several inches at a time, keeping the precision and minor adjustments in small increments. This worked very well. The alignment between the front and back can be off 1 or 2 millimeters. This happened on both sides of the car, but it's not a product flaw. It's that outside stick on relies on the alignment of your door and trim from the factory. If there's any deviation, it might not be seen without visors, but once stuck on, the visors magnify and show the alignment variations. No one has noticed this, it's just my OCD that knows it's there. Cleaning the underside of these visors is difficult. You don't want to wipe too hard to mess up the adhesion or scratch the plastic. Any build up of dust is noticeable from the inside. These negatives are nothing compared to the in channel design so weren't enough to knock off any stars. Ultimately, if you have a specific need for the visors, these are the best I've found. I would buy these again for a similar use case. However, if I didn't have my specific use case, I'd pass on visors all together. If you need visors, these are the ones to get.

I regret to say that my experience with the AUTOCLOVER Tape-On Rain Guards Window Visors has been nothing short of disappointing. I purchased this 6-piece set for my Hyundai Santa Fe 2019 model, hoping to enhance both the aesthetics and functionality of my vehicle. However, I encountered numerous issues that make me strongly advise against purchasing this product: Low-Quality Material: The window visors are made from flimsy, cheap plastic that feels like it could break at any moment. Not only does this compromise the durability of the product, but it also detracts from the overall appearance of my vehicle. Poor Fitment: Despite being advertised as specifically designed for my car model, the window visors did not fit properly at all. They were small ot covering the windows. It's clear that no attention to detail was given during the manufacturing process. Installation Hassles: The supposed "tape-on" installation method turned out to be a nightmare. The adhesive strips provided with the visors were weak and ineffective, leading to constant readjustment and eventual detachment. It took hours of frustration to install these visors, only to have them come loose shortly afterward. Overall, I am very disappointed. I will not recommend.

Excellent results for me on my 2021 Hyundai santa fe calligraphy. Loved the "chrome" top edge to match the existing silver window trim. You must prep the surface properly. You need to clean the full surface repeatedly, especially if you wash/wax your vehicle regularly. I always keep isopropyl 91% on hand and used that on a paper towel a few times back and forth and dried it completely. No issues with adhesion on my end. I was slightly disappointed in seeing the vhb tape was not 3m branded but so far so good. Its been a couple weeks since installed. It's been 40s during the day and 20s at night, it has rained as well. Overall good quality and results in wet weather.

Loved the fit and quality

Super easy to install and looks great. One of the visors did start coming loose after just a week. bought some new 3m adhesive and its back to being normal.

Check your package before using anything my Package was missing parts and I was really disappointed that it wasn’t everything that I ordered in the box

Exactly as described. Fits perfect! Great value. Have on 2 cars!