MICTUNING Motorcycle USB Charger,SAE to USB Cable Adapter SAE Quick Disconnect 2.1A Waterproof USB Port with Inline Fuse, Socket Cable 12V-24V for Motorcycle Cellphone Tablet GPS More

Well made. Easy to install. Cables appear to be good quality and of ample length Even comes with cable ties and spare 10a fuse. Survived deluge of rain with cap on. Not sure how waterproof it will be with USB in use, so positioning of the port is important. Since it has SAE connectors it can also be used as a feed for battery charging from my Optimate.

Great little add on. Able to connect to motorcycle headlight, so ignition acts as switch. If you put it straight to battery with no switch it will ultimately drain a steady charge, thereby creating a flat battery eventually. Although you could just unplug it near the charger unit. Neater linked to the the ignition though. Comes with a fuse in the fuse unit and a spare. 👍🏻

Good product, good VFM. Easy to install. Lot of mixed reports online about whether or not these drain your battery, I can confirm they drain my MT-09 battery if it’s stood for about 2-3 weeks or longer. Just to back this up I’ve attached the current this adapter uses with no device plugged in, which is just under 14milliamps. Definitely worth connecting this to an ignition switched circuit or putting in a relay to avoid flattening your battery. Only criticism of the product itself is the weather proof cover over the port itself is flimsy, mine has snapped off already.

Perfect for my needs Works well as it should Thank you

Fitted to a Harley sportster, so that I could power my phone. Very simple to fit, the wiring is good quality and comes with a spare fuse and waterproofing for the connections. Nice and straight forward

Great little USB Charger, easy to conceal by tie wrapping to the back of the bike ignition, I wired this into my Varadero and its a good item, As I tour North Wales throughout the year I needed to keep The mobile phone topped up as its quite easy to get lost in the Welsh mountains. Very well made and suitable for the job its intended.

Installed on my R125 YZF Yamaha, 2016 reg. I haven't rated the ease of installation rating as this will vary from bike to bike. My motorcycle has a lot of space upfront, fairly airy cowlings so putting cabling in with zip ties is easy peazy. However, the fused back cable barely fits in the tight right battery compartment under the seat. Works fine as a USB, using it to power some LEDs as well as be removable to charge a phone when I'm somewhere new. Worried a bit about rust but trying to keep it dry. I put the port somewhere it won't get directly wet. As long as you take care on installation, make sure the port and exposed metal parts aren't gonna get directly wet or salty, you shouldnt have a problem with this at all. Also, make sure you have your wiring done properly. No shorts or positives to negatives as this will blow your fuses and if you don't have spares, you won't be able to use whatever that fuse powered

Easy to install on my 2004 R6. Easier than similar tutorials on youtube. Total of 4 bolts undone to remove seats and lift tank although tank was maybe not necessary. Wired straight to battery so can charge with the engine off. No comment on battery draining as it's too early. Attached the USB end to the back of the ignition with velcro. No wires to be seen anywhere. Comes with 4 cable ties also. Bargain

El kit viene preparado para fijar rápidamente en los bornes de la batería de la moto. Los cables son de buena calidad y de momento funciona perfectamente. Además tanto los conectores SAE como el USB vienen con una tapa estánca para garantizar que no entre agua si llueve o lavamos la moto.

Waiting to install on bike

Se utilizzato correttamente, non da nessun problema. Ho messo un connettore in modo da poterlo staccare quando non lo utilizzo per caricare il telefono. Anche se entra acqua nel USB (quando è staccato), poi una volta asciutto non mi ha mai dato problemi. La carica è tutto sommato veloce e funziona bene. Consigliato.

I needed this cable to connect USB equipment to a benchtop power supply in a lab. It was to charge a device at ~5V that has no internal current limiting and could draw up to 3A which I needed to limit to 500mA for safety purposes. I set the benchtop supply output to 12V @ 500mA and this cable's integrated regulator was delivering 4.47V at 500mA to the device which was good enough for safe charging. Because the supply was operating in a current limited mode, the effective voltage delivered to this cable's internal regulator was effectively ~6V but it could still regulate just fine. Very impressive! In fact it could deliver stable output with the source voltage as low as 7V. That's a pretty good operating range. The build quality overall is great. It's durable, rugged, and having the built in fuse is great. It also comes with a spare fuse too. Nothing about it seems flimsy or cheap.

Recomendable