Rust-Oleum 214944 Specialty Reflective Finish Spray, 10 oz

Not as reflective

This is the worst waste of Money Ever do not work at all it’s like springwater wants to dry 2 Everything Disappear Nothing Work do not West You Money on this really bad product and you cannot return it the stealing your money please do not buy do not make a mistake I did

Works exactly as I hoped. A couple coats as described in instructions on can and good to go.

Included photo was base coated with Glidden Safety Orange Enamel Paint, Left board was coated with this reflective spray paint, right board had no coating. Looking straight at the board with a flashlight with coating an immediate white shimmer appears, looking at it from the side however no reflectivity could be seen. Coating took away all the gloss orange and left it cloudy matte in appearance. This product would be ideal for mailboxes, parking bollards, fence posts, and haunted houses. Product diversifys greater than a normal spray can it is recommended to have the nozzle 12-18” away from item being sprayed to keep object from clouding up too much, spray gets everywhere if a gust of wind comes up while spraying be sure to cover or remove objects within in 10 feet that you don’t want easily found in the dark. While it was hard to see reflectivity from side with a flashlight it was more easily viewable on infrared security cameras, making this a great product to apply as backdrop to see things walking in front of the paint on camera.

Works as expected

Doesn’t work

I have wanted reflecting wheels for my bike, but what few are made are very expensive and my bike takes an odd size wheel. When I ran across the listing I was thrilled, but concerned as to whether the paint would work at all because of so many bad reviews. Well, I generally followed the directions on the can and the result is a very reflective wheel rim. Here is what I did: 1) taped off the parts of the wheel where I didn't want paint (obviously). This is a bit of work, but fortunately I was working with the rim only and will build up the wheel later. I used the wheel as a template and cut curves in the blue painters tape so I could mask the machined sidewalks of the rim. 2) shook the can very thoroughly. This is very important because this "paint" is a clear coat carrier for super tiny reflective beads. It is these beads that makes your item reflective, if they are not mixed in to the stream you are spraying at your object, it will not end up reflective! (Think unshaken vinegar and oil dressing.) 3) shook the can again after every 15 seconds of spraying, according to directions. 4) did three very light coats 2 minutes apart. While I was waiting between coats, I kept shaking the can so the reflective beads and the clear coat paint wouldn't separate. After drying, I tested in a dark room and a flashlight and it was definitely reflecting. I noticed that from some parts of the rim (the flats parallel to the ground) were super bright white compared to the rim sidewalls. This can only be from the higher density of beads. This gave me the idea to add more paint. I repeated steps 1-4 after 24 hours. The brightness of the reflectivity increased dramatically. Even the blue painters masking tape is shiny. I may do a third round as an experiment, although my buddy says it looks great already and should stop. I bought another can to do more wheels.

This transparent reflective paint doesn't reflect light at all. I sprayed my mailbox with it for several coats and it didn't reflect my car light at night. A regular white paint or light color paint would do a better job than it.

Does not work as described. Reflection is too low.

Used this to spray over the registration plates on my cars , trucks and motorcycles . it is so reflective under standard flash photography , like in the case of say ......photo radar or red light camaras ...... the entire plate reflects with such intensity that the image in unreadable . Use this info as you please :)

100% work No more tickets 🎟️ Hoooooory I will drive as fast as I can 🥫 😍

رديئ

I followed the instructions to the letter. Shook the hell out of the can as instructed, applied thin layers and all it did was make my number plates hazy but definitely not reflective.