WALI Tall Monitor Arm Mount for Desk for 13-34 inch Screens, 22 lbs per Arm | Single Extra Tall Monitor Mount, Full Motion with Tilt, Swivel, Rotation, VESA Mount 75/100mm,for Office/Home (M001XL), Black

The Wali Single Monitor Desk Mount works better than I expected. First, the basics. The mount comes well packed and the instructions are very simple to understand. There is so little assembly required that the instructions are almost not needed. Assembly and installation can be done in less than ten minutes (not including cable management if you choose to use that feature). Adjusting everything is easy. Overall quality of the parts and the assembled product are quite good. I have two monitors that I wanted to mount on a flat desktop. I needed to be able to get the monitors right next to each other and still have the desk flat against the wall. Most double monitor stands will not allow for this unless your monitors are the perfect size for the spread of the arms. The movable arms will usually flex toward the wall if you want the monitors to be edge-to-edge with each other. The result is the desk having to be offset from the wall to accommodate this. By using two single monitor stands, I am able to move the posts to positions that allow the arms to be extended in such a way that everything is flat with the wall. The other frequently stated issue with most monitor stands is that the arms have hydraulic pistons and/or springs to deal with the weight of the attached monitors so they are easy to move up and down. These pistons and springs are often of poor quality and either fail quickly or don't work as expected from the get-go. This is not a problem with the Wali Single Monitor Desk Mount. The arm is solidly attached to the 16" pole and only moves up and down by loosening the arm mounting and sliding the arm up or down on the pole. The arm, once set to the desired height, can be move forward, backward, side-to-side and tilt. This makes for a much sturdier setup with no pistons or springs. This system works very well, since I (and I think most people) have little need to move a monitor up or down after the initial installation. I leave the included Allen wrench stuck in one of the vertical facing screws behind a monitor so that it is always handy but out of sight. If I do need to move the monitors up or down, the tool is right there. I will buy two more of these for my wife's desk.

I bought the 31.5 model to mount a 27" monitor above a 32" monitor on my desk. This is the first monitor mount I have ever purchased and I am thrilled with the entire mount! The installation instructions were simple to follow. All hardware was clearly notated and packaged by part number. The mount holds the 27" monitor (which isn't all that light) perfectly above my desk monitor and is very stable. Adjustment is easy and effective and It doesn't wobble one bit. The cable routing clips work well and are literally a snap to install. I used the clamp mount but a screw-down desk mount is included.

This monitor mount is heavy duty! Sturdy, well built, and can mount two different ways. I have a keyboard stand with an upper shelf. I installed the monitor mount using a center slot I had cut into the shelf and it was a breeze installing it. My video monitor is small and I wanted it just above my music rack which sits toward the front of the shelf. I have a video system combined with my keyboard so I can watch movies while practicing. I highly recommend this monitor pole mount. Great value for the money. Monitor can be moved in a plethora of positions.

For the price, I’m pleased with it. Overall, it’s a sturdy stand with quality machining. All the screws went in easily, poorly machined products have crooked holes or bad threads. The mount base comes with 2 types, standard mount for a desktops surface. The other one is for desktops with monitor holes/cabling drilled through them. All the parts are heavy gauge and I encountered no difficulty during assembling. There seems to be a tension screw for the tilt feature. I had to tighten the screw that holds the tilt joint together because out of the box, the monitor flopped forward hard. I had to be mindful while mounting it to the main arm so it wouldn’t slam into my glass desktop. The 2 arms that allow you to move the monitor forwards and back, left and right were a little stiff, I loosened the screw a bit on the main arm, at the pole. That seemed to be all that was required. I tried to loosen the bolt where the 2 arms meet, and it wouldn’t budge. I didn’t force the issue. The instructions were adequate for assembly without covering anything else, like adjusting the tilt bolt for the weight of the monitor. So, while I think this was a good mount for the investment, there are tradeoffs to mention. I’m accustomed to swinging my monitors upward and dusting underneath them. Height is fixed by a screw on this one. I was struggling to install the monitor cables when I realized you can tilt the bottom toward you until the top or the monitor hits the pole, or, until it’s sitting nearly flat like a table. Elevated several inches above the desktop. I consider this a Pro / Con feature. Where the arm ties into the VESA mount, the fit is a little sloppy. It’s not a safety concern but I can wiggle the monitor backwards and forwards at the outer edges “About ¾ inch “before feeling any resistance from the mount. Same goes for tilting. I don’t see this as much of an issue. Normally, I don’t foresee any outside forces acting in the monitor to create a problem. However, there’s room for improvement. The rest of the machining seemed steller. I have multiple computers in different rooms. 32” monitors are used as primary monitors with 32” to 23” as secondaries. I like mine roughly 1” above the desk. That places the top of the monitor at my eye level and the ideal viewing angle. I have fully articulated, hydraulic mounts on most of my monitors. Nice ones for large heavy monitors run $75 to $100 and up. I paid $36 for this one. The……… WALI Monitor Arm Mount for Desk, Single Extra Tall Computer Desk Mount, Monitor Bracket Mount Stand Single, up to 32 inch, 22 lbs (M001XL), Black. Amazon lumps the reviews of similar products together, so I specified which mount I purchased. I’m using this one on a glass desktop, I’m attaching it to the same point I constructed from wood for a different mount. It didn’t lower the monitor low enough either. So, the top of that mounting point is 4” lower than the surface of the glass top. Despite being that low, I didn’t actually need the 32” pole / monitor mount, the 16” model would have worked. There’s still 2” of pipe available above the arm. The 32” was on sale & I didn’t know if the 16” would suffice. The pole is a screw together 2 piece. I unscrewed / removed the other pole as it looked out of place in my dual computer setup. That leaves a hole in the top of the pipe / mount. I wish they included a cap for that. The top pipe has a cap but of a different diameter. I’d like to give it 4 ½ Stars but Amazon won’t let me. I’ve got to go with 4. Height adjustments with heavy monitors and an Allen wrench can present a challenge, it’s the nature of the beast and I won’t give it 5 stars for a few reasons. The sloppy VESA mount and loose tilt motion. No instructions that cover that, or if I was supposed to loosen the arm at the pole to improve motion. I would recommend this mount to others.

I wanted a mount that worked with a desk grommet while still allowing cables to go through the hole, would work on a narrow (22") desk attached to the wall without making my monitor stick out past the front of the desk, and was under 20" tall so it would fit under the overhead cabinets. This mount hit all of the marks! Installation was fairly straightforward. The only issue I had with the whole install was that the VESA mount screws were a tad too long, leaving the bracket a little less than snug. I grabbed a couple spare washers from my garage, and I was back in business! I like that I can lock in the height (have to tighten it with the allen wrench, but I don't intend to move it often), the arm articulates well, and it supports rotation. I also like that the VESA mount is in two pieces, which allowed me to mount it to my monitor and then slide it into place on the arm, securing it with a cap nut. It feels secure, AND I get to recover the space underneath the monitor (and permanently evict the dust bunnies!) I paired this with a small rectangular USB 3.0 hub, which I was able to zip tie to the arm, allowing me to hide all my peripheral attachments. The included cable management is simple and does the job. Super happy with this purchase!

I recently purchased an LG 32UN500 monitor weighing ~17 lbs. The included monitor stand was not great according to the reviews so I opted to purchase another stand. The WALI would take the load and it appeared solid. Assembly was straightforward. I opted to put a hole through the desktop for the stand. The monitor came with its own screws for the VESA mount so I used those. Once assembled I adjusted the arm height and tightened the arm to the stand so it would not slide. I then placed the monitor with the attached VESA mount in the arm mount and attached the nut to secure it all in place. Adjustments are easy with the supplied Allen keys. The stand allows me to tilt, swivel, and raise/lower the monitor height. Solid product that does the job it was designed to do at a reasonable price. Adjusting the height does require loosening the fastener so if that is required frequently you might consider another stand. One last point, the attachment to the desk requires so little space that I have regained all the space I lost to the stand for the previous monitor.

This is the monitor mount I should have had all along. The extra tall pole allowed me to mount my 32" monitor at the correct height (something I couldn't do with the spring-mount I previously had. It came with good directions, everything needed for install except for a Phillips head screwdriver and a 10mm wrench for one cap nut. The arm that holds the monitor is highly adjustable, and once everything is tightened down, very sturdy. I recommend this one without reservations.

Overall, this is a great product considering the $27 price tag. Looks nice, seems sturdy, and necessary tools are included. Pros: - Lightweight, easy to assemble and adjust - Appears sturdy based on initial use - Aesthetically pleasing - Plastic cable hooks are useful for cable management - Significantly reduces monitor wobble when typing (vs. factory monitor stand sitting on desk) Neutral: - C-clamp base is massive at 3" x 3". This is almost certainly necessary for stability / safety when mounting heavier 27" monitors, but still unexpectedly bulky. The width is mentioned in the product pictures, but both width / depth could and probably should be explicitly mentioned in the product description. My PC desk has a 2" overhang, with a slightly beveled edge, so I used a dense piece of cardboard underneath the overhang to ensure that the clamp was flush and level. - Arm cannot be folded flat against wall due to inherent design limitation (180 degree joints), so vertical post must be placed off-center if desk is against the wall. So if you plan to move the monitor forward / back and want to keep it centered on your desk in any position, expect to do some fiddling with the mounting location of the vertical post. This is not really a drawback when you consider the price tag, and if you have space behind your desk this is obviously a non-issue. Cons: - One cable hook snapped as I was attaching it to the monitor arm, but I was able to make a flimsy repair with packaging tape. Note to anyone considering this mount for use with a TV instead of a monitor... some manufacturers (Samsung in my case) use larger or non-standard VESA mounting sizes such as 200 x 100mm. I purchased the following Mount World adapter plate along with four M4-.7mm x 10mm flathead screws / nuts from Home Depot. The adapter included a bag of various nuts / bolts / washers, but the provided flathead screws were unfortunately too large to fit the original VESA plate included with the WALI mount. Mount World 1056 VESA 200 x 200 Universal Adapter for Medium Mounts

43インチモニターを購入し、 高さが欲しかったのでポールの長い本商品を購入しました。 翌日配送できましたが、到着して開封してみると本商品はポールを2本連結させるようなのですが1本しかはいっておらず返品しました。 型番を確認すると M001XLと製品ページではなっていますが、届いたのはM001SXLでした。

Bought this to hold 32in monitor above imac 27in, does the job and very good quality.

I have used some of the monitor arms' pieces to put together this triple arm to hold my heavy giant print study Bible on a tray at bedside. It fits on my old Ergatron short desktop pole. It's far easier to just need to tilt the tray than to pick up and hold the heavy book.🙏 The 31" WALI pole is used in the loungeroom for my computer set-up along with a few of the monitor arm bits, plus a WALI 3 Tier Arm. (another review😊) Good stuff these WALI products, and well worth the money.

Good product

This is great - all metal and very solid. It’s probably not as adjustable as others, but for the price it’s great value and works best for a monitor that won’t be moved often.