3S 4S 12V 5A Battery Active Equalizer BMS Balancer Lipo Li-ion LFP LiFePO4 Lithium Battery Balance Active Energy Transfer Equalization Module Faster Whole Group Capacitor Balancer PCB

worked great to balance my 200AH RV batteries. Cells where ranging from 3.6 to 3.2 a few hours after installing this they where all the same.

Balanced my M18 12Ah overnight from 150mV to within 5mV. Very happy as the design brings the cells into equilibrium in lieu of designs that bring everything to the lowest cell voltage. At start I measured just over 20mA of current. Was surprised to find the next morning everything was balanced. It has a run light that was still on in the morning. Idk if it was still balancing but good enough. This was a battery I replaced 2 bad cells in. Nice for money. No frills, need a meter to confirm results.

I'm sold. These little guys just work. Latest build is a 4S2P 12v LIFEPO4 and the cells have been as much as .20 out of balance while charging. Within a couple hours they are exactly the same. I've read some horror stories with these and the main thing to.prevent problems is to install these before the battery pack is a mess of mismatched voltages.

This Active Cell Balancer is great! I had a very unbalanced 12 Volt (3 series) Li-Ion battery pack and it gradually brought all 3 cells to the exact same voltage (within a couple miliVolts of each other). What I really like is that it balances the cells regardless of their voltage or state of charge (unlike the passive resistor cell balancers which only work when the cells reach 4.2 Volts). This is my favorite feature since I only charge my cells to 4.0 Volts (approximately 80% state of charge for long term life). I performed a very careful measurement of the quiescent current and it is less than 10 mA (so no problem for my setup to leave it running continuously). A great product!

I found this battery balancer very useful and effective. I used it daily for months, but it died due to my error. Please triple-check the battery pack's resistance. I failed to notice a dead battery with high resistance, and the capacitor exploded and melted my silicone mat. The photo shows the melted area on my mat.

Balanced a badly unbalanced 7s3p Li-ion battery in just a couple of hours. Much more effective than resistive balancers.

Voltage would drop to 9v over night but after disconnected from balancer, slowly discharges normally.

Simple to install. Checked with my clamp meter and it would transfer up to 2 amps on my system. Though it balances more aggressively than a BMS, if batteries are way out of balance I recommend parallel balancing batteries first. I also recommend taping some barley paper over the exposed circuits to prevent short circuits.

Yo el puso en un pila de 12s y 48v si hace su trabajo

Connected this balancer to a 6S2P bank of SCIB 20AH LTO cells and after a few hours it had every cell within 2mv of eachother. Unlike other balancers that only balance when near full charge this balancer continues to operate throughout the voltage range so take that into account when choosing the best balancer for your application.

Balanced like a champ for 10 minutes after I got it installed on a 16S LiFePO4 pack. Would be a great unit, if it didn't let the smoke out and stop functioning.

Never got to use it. Maybe it is meant for an experienced user, Other than wiring order, has no information. Does it need to be used with a charger, Does the BMS have to be disconnected ? Do the batteries have to be fully charged ? When should it be used ? It is a new type of balancer (Capacitive) I don't have time to spend looking all over the internet only to see people arguing pros and Cons. I am using Daly Smart BMS, but it has a different plug for the balancer. It would be a good idea to use a standard plug, so you could just unplug the wires from the BMS, and Plug them into this device.