J-B Weld 37901 ExtremeHeat High Temperature Resistant Metallic Paste - 3 oz

I purchased this item to repair an ash fettle in an old Vermont Castings wood burning stove, and it completely exceeded my expectations outlasting an entire season of direct fire contact. The fettle was cracked into two pieces and a prior owner had drilled two holes on either side and tried to connect it with an aluminum "bridge." The repair interfered with the door closing, so I needed to seamlessly "weld" the two cast iron sides back together. Before going through the trouble of taking it to a welder and paying to have it repaired properly, I took a chance on this J-B Weld ExtremeHeat. I used a Dremel tool with a fine grinding stone and cleaned up the two broken faces, along with about 1/4 inch of the area on either side of the crack. Following the advice of another review, I then took a cotter pin, stuck it into the chuck of my battery powered drill, and used that to thoroughly stir the J-B Weld in the container (this is a one-time use container... once opened and stirred, use it and toss the rest). After stirring for just under 2 minutes, I immediately applied it to the two surfaces, pieced them together, and then spread a little more on either side to ensure a supported bond. I then set the item on a flat piece of cardboard to cure for 2 days. (NOTE: you have to support the joint while curing, because the J-B Weld provides no structural support until completely cured. While wet, the item will just fall apart again if the pieces aren't otherwise held together.) When it was done, I replaced the fettle and lit the first fire of the season (crossing my fingers at the same time). Several months and probably 100+ fires later, the piece was still holding strong like the day I put it in. The fettle sits right against the fire, and many logs have rolled into it while it was extremely hot, with no noticeable damage whatsoever. I would absolutely recommend and use the J-B Weld ExtremeHeat again on future projects. As long as the proper preparation is done, and you follow the instructions, it's an awesome product!

Worked well for sealing my exhaust fittings. Easy to apply since its a bit thick, use it all in one go cause it isn't usable afterwards.

Probably saved me a lot of money on a repair job at home. I used this J-B Weld Extreme Heat to fix a crack in my cast iron skillet. It bonded well and restored the smooth surface. I'm glad I gave it a try.

If you use it for deep hole filling it takes more than an hours to set, it is strong but not that strong you can brake it with your fingers, if is applied on hot surfaces it tends to shrink.

Someone had drilled holes and used an aluminum bridge, which caused issues with the door closing. I decided to try this J-B Weld ExtremeHeat before spending money on professional welding. It worked nicely to bond the cast iron back together smoothly. Very pleased with the result.

Bought this due to the high temp claim. tried it on my small 24 hp kohler exhaust pipe that 90's angles into the muffler, sealing around the pipes. Firstly it completely separates sitting in the jar for more than a day. Once stirred up it turns to the gray color of standard jb weld but the consistency is more watery and drops instead of staying in place. i allowed more than 24 hours ( 1 week) to cure before running the mower. After a lawn cutting (about 45 min) I can see half of this jb weld has cracked and fallen off, the rest can be popped off easily by hand and I tried to layer after finding it failed the first time, that didn't make a difference. I will just end up actually welding the joints vs this junk. I was really hoping that this would work since their normal jb weld stuff works well. it also it turns white once a heat cycle has been applied to it, it doesn't stay gray in color.

I followed the instructions on this product well and while it did perform better than the squeeze bottle J-B Weld high temperature muffler repair, this product still cracked under frequent hot-cold cycles on an exhaust system. It did last longer than the dedicated muffler repair product which is why it's getting at least the 3 stars.

Kneeling the 2-inch adapter into position, I utilized this product as a filler between two components that sit directly in the same cup without a divider. I wrapped a stainless shim around it to ensure a snug fit and secured everything with a clamp. So far, it handles thermal changes pretty well. I plan to see how it holds up after a week. I'm pleased with how helpful it’s been so far. An AI tool mentioned it has good adhesive qualities and durability, although I haven't tested those features myself yet.

kanon

Amazing result. Used on an old gas oven door. Unable to get parts to repair handle but this product did the trick. Very pleased.

I bought it to fill the gap developed in high pressure vessel..it is very good and handy in such situations..highly recommend.

Reparer un coude d’echapement sur un bateau le temps d’avoir la piece de rechange.

I wasn't expecting much, but JB delivered. No solvents, great repair to my exhaust silencer. Top marks.