Grip Puppy

Huge difference. I can barely feel the vibration on my hands at high rpms. I have them installed over my arlen ness grips. Perfect fit as far as diameter and length. No need to cut. Just used some waterless car wash spray and they went on easily. Twist and push in. Very comfortable and squishy enough to grip with no effort.

Very comfortable, they absorb vibrations very well. The bad thing is that they only lasted two seasons

I was prepping for the Daytona Rally run last month and ordered these. The premise was that the extra cushioning would cut down numbness and such in the rider's hands. I broke my wrist when I was younger and my right throttle hand goes numb pretty quickly unfortunately. ANYTHING I can do to delay or prevent that is a plus. First trick was getting them on though. Read MANY "Here's how I did it" things. Did the hot water, tried the dish soap. What a pain in the "you know where." DO THE AIR COMPRESSOR METHOD. I fought and fought before I broke out the compressor thinking that it couldn't be that hard. It was. Pinched the end of the grip around the tip of the air gun, gave a little blast and it was about halfway on in a split second. Had to fidget with it a bit keeping the air blast in there enough to balloon it up to move on further. Still took some effort and fidgeting, but yeah, that was the absolute best way. It is tougher as you get it nearly on as it's almost impossible to pinch the end around the air gun nozzle. It will eventually get there though. Might have tried a longer needle tip to get further inside the nozzle. Don't HAVE one, but I bet that might be the trick. Did it work AFTER I got it on? Yes. My right hand often goes numb in just a few minutes without flexing it around. I have a feeling that the extra circumference on the grip as well as the cushioning was a huge improvement for me. Was able to ride pretty happily for much longer without having to shake out that hand. They're staying on! As well, as in the pics, I was able to add the throttle control back over the top of the grip. ALSO took a little fidgeting, but it's on, works great. SUPER HAPPY with my setup now.

Installed over the stock grips on my '22 Heritage Classoc114. Seriously tight fit and enlarges the grip size. The material is comfortable. I have carpal tunnel and a cervical spine injury with residual radiculopathy post multiple surgeries. I haven't noticed much relief yet, but my circumstances are perhaps somewhat exceptional. They are comfortable and much easier on the grip. They are the right price and made well. You may want to trim the throttle side or at least be mindful of the possibility of creating resistance on the medial throttle housing. Once it is all the way on it is a booger to back it off. Overall I say they are worth a try.

I had doubts about these puppelies, but i figured what could it hurt? I have big paws and the stock grips were a bit too small for me so i struggled with balancing the throttle with the clutch and my hands would go numb after about 30mins of riding. (Probably didn't help that i death gripped the handle. Put these on relatively easily. (The ziptie trick worked wonders). Well i really got to test these out on a spontaneous ride that lasted about 10 hrs with short stops in between. Improved my ability to seamlessly balance the throttle and clutch and my hands don't go numb anymore. 10 of 10 would recommend if you have big paws

Does what it suppose to do really well, abit expensive, but worth it. Perfect tight fit on my Moto Guxxi V7 No more carpal-tunnel.

Easy upgrade for hard grips. Got rid of the tingly feeling during long rides. Quick install and material has held up well so far. They're just the right thickness for me. They don't impede your lever control.

Was looking for a solution to prolonged vibration at high rpms on the interstate, and though these appear to be simple solution they are very effective as well. Have had them on my bike for two long trips both close to or a little over 1000 miles each and these performed beautifully. No numbness, no slippage or affect on performance. The only struggle was getting them on. I opted not to cut them since they could extend the length of my stock grips (2018 Honda shadow Aero 750). it would be nice if they included instructions on the methods you could use to install them however youtube provides many possibilities from compressed air, to soapy water. The Foam is very durable. I was concerned about ripping it while trying to get it on but as long as you don't use any pointed objects, it can handle the pulling and tugging to get it over the grips. I used zip ties along the length as separators in-between the foam and the grip as I installed. You can cut these grips down to smaller size if you need to, but I would take my time so you have an even clean edge. If you have a need to remove them , it's very easy to just roll them back off the end of the grip, no damage done to the puppies or your grip. My cramp buster also fits over the foam grip no problem. Great product and does the job.

These are awesome. A bit of soap and they were on in a minute. These are thick. Comfortable and are going to last. I absolutely recommend them

Perfetto per Harley touring.entrati senza particolare fatica .molto morbidi adesso col diametro maggiore devo provarli meglio in viaggio aggiornerò. Montati montati con un po' d'aria per gonfiarli all'inizio e spinti dentro in un attimo

Bought these for my Vulcan 900 custom and has almost completely eliminated the uncomfortable vibration on my throttle hand

Produtos de boa qualidade e preço

Gia usati su un'altra moto e devo dire che sono eccezionali.