GS Power Engine Hood Hinge Ditch Brackets for mounting Auxiliary Off-Road LED Pod Work Light. Fit Between Hood & Cowl Panel at Windshield Base. Compatible with 2016-2020 3rd Gen Toyota Tacoma

Installed on 1st Gen Tundra. Fit well with good clearance at windshield. Hood does sit high but could be lessened by filing the bolt holes or relieving the wiper cowling, I did neither. Installation is easy, just remove lower hinge bolt, install bracket, install and snug bolt, remove upper bolt, rotate bracket to align with hole, install bolt, tighten both. Repeat on second hinge. Took me less than 10 minutes. Product seems beefy with good finish and paint.

Worked a treat and bolted right up to my Lexus GX470. Sweet deal for the price. I don’t think the finish will last years, but for the price it’s almost worth replacing every 3+ years.

Great product. Super affordable way to mount some ditch lights. I’ve had them for over a year and they don’t rattle on and off road

Almost perfect fit on a 1st generation Toyota Sequoia (2001-2007). The slotted holes are slightly too short in distance and will need to be grinded down in order for the screws to be seated properly. I had to grind down the rearward hole (hole closest to the windshield) to move the bracket forward towards the front of the car. This is to ensure that the bracket doesn't hit the windshield when the hood is opened. Also, the windshield wiper cowl will need some modification for the hood to sit flush with the fender. It's not necessary but if you don't then the rear of the hood will sit a little higher than normal. More work than I expected but this wasn't intended for my vehicle. For the value it's not too bad at all! The price is great, but the extra work needed made it fall short of perfect. Minus a star because it wasn't as solid with the light I had on it. It was a bit flimsy and shook a lot on bumpy roads. A solid 4.8 stars in my book.

Easy to install. No mods. Only tool needed is 12mm socket. THESE GO BETWEEN BOLTS AND HINGE! Not between hood and hinge. If you install that way the hood will sit proud and latch awkwardly. To install, remove bolt closest to front bumper, attach mount with other hole offset, replace/tighten that bolt, remove rear bolt, swing mount over into place, replace bolt and tighten. Doing it this way keeps the hood from shifting around so you don’t have to readjust it in relation to latch. SEE PICS

Great ditch light bracket. Designed very well and sturdy to hold lights.

Better than expected considering price, paint like other reviews is pretty thin but if yours careful putting them on its no big deal. How to install these since directions werent included: Get a couple blocks of 2x4s to wedge in between the hood and the windshield to try and limit moving (dont go crazy just make sure the 2 blocks are snug up between the windshield and hood on whatever side you are going to start with. Then remove both bolts on one side of the hood whichever side you put the blocks on to limit movement, I placed mine with the end of the mounts pointing out away from the truck. But you can point them facing in if you desire. Next put the bolts through mount and into their respective holes on the hood and tighten them down, I did this until they felt as snug as they were when I took them off, probably around 30 lb ft. Then move your blocks to the other side and repeat. I installed 3 inch cube lights they were about 4 inches long and 3x3 inches in height and width and have no problem with clearance from the windshield.

Bought for my 2017 Tacoma knowing it wasnt specified to fit, on the upside it will fit as it comes, but with a little know how it will fit perfectly. Overall decent design, bends are nice, powder coat is nice, NOT great, but definitely not the worst I've seen from an Amazon product. However there are a few areas that are applied chunky or have some marred edges. Thickness is also fair and not flimsy. All in all, you could get MUCH worse for your money. Would recommend.

Fits 2010 Tacoma. Easy install and great product for the price. I read some comments about thin powder coating but I had no issues with these. Very happy with the results. Would buy again.

These hood brackets for ditch lights are great quality! The powder coating is solid and the holes for the brackets lined up correctly.

Bien construit, peinture semble de bonne qualité mais pas eu la chance de faire l’installation encore

Bracket with without issues on a 2018 Tacoma. Powder on the bracket is good but however the stamp finish is crap. Sharp edges are pointed towards the hood and the opposite side has a rounded edge which will not grab onto the paint/ cut the hood. This is only for the driver-side bracket so be careful when installing. Other than that - solid mount, wasn't able to bend.

This fit perfect just what I wanted