SummitLink Snap On/Off Prop Guards 2X Red 2X White for Phantom 1 2 3 Quick Connect Tool Free Also Fit on Phantom 3 Standard

Very well packaged and great attention to detail. I was slightly skeptical after reading other reviews, but as of October 2015, mine came with two sets of screws, each labelled, one for Phantom 1 and 2, and the other for the Phantom 3. Next pleasant surprise was that there were two Allen wrenches included, one to remove the original phantom motor mount screws, and the other larger size for installing the new mounting screws for the Phantom 3 (the one I bought). I also skeptically checked the length of the news screws and they were exactly the correct length when adding the depth of the new prop guard mounts, so no trouble at all installing. There were also 18 screws, not just the required 16 in my Phantom 3 bag, nice touch. Upon removing the original Phantom screws, I noticed a very small amount of blue Loctite at the distal tip of the threads, so put a similar small dab of blue (medium) Loctite on the new screws. When installed, the fit was perfect for the original blades for the Phantom 3 Professional. (I did not use the cord to connect the outsides of the individual prop guards.) I kept the original screws if I decide I don't need the prop guards in the future. Great option for me as a new Phantom user.

I've been flying DJI Phantom since DJI Phantom 1. To date, I've owned three DJI Phantoms and this is the first DJI Phantom that I have installed props guards on. I intentionally didn't install prop guards previously because they made the DJI Phantom 2 or DJI Phantom 2 Vision Plus too large to fit inside of a carrying case. These prop guards are EXCELLENT because they quickly snap off without tools! It's easy to land the DJI Phantom 2 and have the prop guards disconnected a few seconds later. These prop guards pay for themselves by saving propellers! Even the most skilled DJI Phantom pilots damage props unexpectedly upon landing. These also help to reduced prop damage while bumping into an object unexpectedly during flight. The quick-disconnect piece remains attached below the four motors. Installing that piece was a simple process. It's just a matter of replacing the factory DJI screws with the longer screw that stick through the quick-disconnect piece. These prop guards have not degraded the flight dynamics of my DJI Phantom 2 in any way and the red color pieces are great! I mounted them on the front of the DJI Phantom 2 to function as a visual way to see which end is the front of the Phantom. I'll never fly a DJI Phantom without these prop guards! I'm so glad that these prop guards were brought to market!

Four stars because these guards are tough, light weight, slip on and off easily and do a good job of protecting the propellers, but cost aircraft performance. I installed these on my Phantom 3 and noted the following:26% reduction in top speed.Reduced climb rate.Reduced maneuverability (roll and pitch rate a little slower).Guards are visible in the camera view when cruising at higher speeds with the camera set level.They will work great for most of my slow speed flying close to obstacles and will save a lot of broken propellers. But I'll probably remove them for flying in the wide open. The easy-on, easy-off feature is great for taking it down to pack it in the soft case. And I can still get it into my cut-out soft case with the guard receptors in place. There are no stability problems when descending with these guards in place as some have reported on YouTube. I have descended with full down stick and the drone was as stable as it is without the guards.

bought these for my DJI phantom 3 standard. comes with everything advertised. well built adds extra protection for the arms, the quick attach unit screws onto the arms easily, the guards can then be put on quickly, and taken off quickly for storage. great to use for indoors or areas with brush or trees, also helps if you have any tip overs. protects both drone and blades. Also helps with visibility of the drone. good product, good price.

These went on so easily and they work perfect. They did change the sound of the wind passing through them a little, but once the drone is 10' away you can't hear it much anyway. It has already saved my drone and one day it was caught in a tree. I got on a ladder and extended a 20' pole to the drone, speared through these prop guards and it slid right down into my hands without a scratch on my Phantom. Very very sturdy. Great protection. I would definitely buy again, but I don't think these will break.

Prop guards are a must have for any skill level because they greatly mitigate the damage to the props caused by the nuisance bumps and nicks that WILL happen even to the most skilled drone pilot.I give overall Quality a 4. The guards feel thick and sturdy and not at all "flimsy" as some others have stated. They are heavier than the branded DJI prop guards for the P3. I take off one point because they feel a little rough and unfinished. However, the fact that the red guards give a larger visual reference to the front of the vehicle is extremely useful.Installation is quick and intuitive. I take no points off because there are no instructions - none are needed. Its like saying that you take off points when reviewing a pair of shoes because they didn't come with instructions. If you're intelligent enough to figure out how to fly and control a drone, you don't need instructions to install these. It took less than 10 minutes for all 4. And YES, the installation screws are a different size but they included all tools required for installation.The ease of removing the guards is invaluable to ensuring portability. You can have the props and guards on or off in under one minute. And finally, I did not perceive any performance degradation or flight characteristic changes.

I purchased these prop guards for my brand new DJI Phantom 3 Professional quadcopter. I was a bit hesitant to install them because a few reviewers on Amazon complained that the long screws included in the Summitlink package were too long and damaged the P3P motors.However, the prop guards fit perfectly on my quadcopter, and the screws are NOT too long (even when fully tightened). The guards are a bit annoying to install because you have to remove 16 screws from the chassis, but once they're on, they fit very snugly and are rock solid. The build quality is good: I tipped my drone yesterday because I tried to land on a slanted surface, and the prop guards saved the copter from a potentially very expensive impact.A side note: after installation is complete, it may appear as though the angle of the motors has been altered (normally, the four motors point outwards slightly to increase stability). However, as long as all 16 screws are tightened firmly, the motor mounting system will prevent the motor angle from changing. Just something to keep in mind.Get this for your P3P or P3A. You won't regret the purchase, and the quick disconnect system is awesome. Would recommend! It's worth spending $30 on these prop guards - it could save you hundreds of dollars in the case of a simple tip-over or tree encounter.

The guards arrived on-time and in good condition. I also have the original DJI non-removable guards but I bought these because I could not fit the drone in my backpack unless I removed the guards. Installing the DJI guards requires you to unbolt 16 small screws. The removable guards come off in 2 seconds, yet stay on firmly. I found the DJI guards to be made of better quality plastic, stiffer/stronger but the Summitlink guards did the job. One thing I didn't like about them is they had a ton of flashing. For those that don't know flashing is extra plastic that squeezes out between the mold halves when the parts are made. This is due to poorly made molds or worn out molds. The flashing was mostly a cosmetic issue but some of it did interfere with the on/off process and I had to remove it by hand. The flashing was pretty much everywhere the mold halves met and in many instances sharp. So I ended up scraping all the flashing off. Another thing to consider was that the replacement screws are longer (due to the extra thickness of the snap on mechanism) and do add extra weight far out on the ends of the drone. I did not have the time to measure the actual weight difference or to see if this had any measurable effect on handling or battery runtime, but the extra weight is probably negligible. For the price I find them acceptable and perform the function they were designed for (keeping the props from hitting obstacles).

注文から発送、自宅まで１日で到着しました。取り付けはモーター取り付けネジを4本外し付属のネジに交換するのみです。六角レンチも付いてます。プロペラガードの赤色が上空でもよく目立ち、機体の前後が見やすくなりたいへん満足してます。使用しない時は簡単に取り外せますし、モーターマウント部分の補強にもなり宣伝するわけじゃありませんが、phantomをお持ちの方は皆さん取り付けられた方がいいと思います。

Good product

ファントム3スタンダード用に購入。正規品のガードをつけていましたが、しょっちゅう取り外したりするには何かと不向き。付けっ放しにしておくと何かとかさばるので・・・この商品を知り購入。ファントム本体側の取付けは付属のネジで容易にできました。そこにガード側を差込む時に最初は製品の形成バリが邪魔をしてスムーズに脱着できませんでした。いざ外す時に抜け辛かったです。気を付けてカッターで削ったりヤスリをかけるなどして滑らかにしてやる必要がありました。そのあとはスムーズに脱着が出来る様になりました。取り外しができると、ほぼノーマルのサイズと変わらないのでいいですね。市販の車載用収納ケースに入れて持ち運びするのに大変助かってます。

機能としては十分で、簡単に取り外せて便利ですが、アーム先端が厚く大きくなるため純正のケースに入りません。リュックだけでなく、アルミケースでも緩衝材をカットしないとダメです。特にリュックの場合は余裕が無く、他のパーツとの間隔がわずかしかとれません。結局オークションでかぶせ式の取付パーツを入手、純正ガードの組み合わせで使っています。

値段が値段なのでバリ取りが雑でカッター使って自分で取りましたがその他は取付も簡単でしっかりプロペラもガード出来るので使いにくい純正品よりお買い得です。